TALAS3. 6 TALAS RC2 & RInstalling Your Fork |. You Ride | Setting.
High- Speed Compression |. Low- Speed Compression |. Safety Information.
Von mir verwendet und fürs Service empfohlen sind diese Produkte: ALL You Need : Fox Service Kits: http:// Montagematerial: http://amzn.to. 2013 Float CTD shock models. Shifting the focus to the front of the bike, FOX unveiled a variety of new updates to their FIT fork lineup. 650b seemed to be a key.
RC2weight R5. 2. 7 lbs./2. TALAS 1. 60+1. 30+1. RC2. TALAS II travel adjust, low- speed compression, high- speed compression. RTALAS II travel adjust, hydraulic bottom- out in damper, air spring pressure.
RC2 FIT damperintended usecolor. TALAS Blue. Be sure your fork is properly installed before proceeding. Clicking. on the link above will take you to a new page. Before You Ride. Check that the 2. Clean the outside of your fork with soap and water. Do not spray water directly on the seal/upper.
Do not use a high pressure. Inspect entire exterior of fork for damage. The. fork should not be used if any of the exterior parts appear to be damaged. Please contact your local dealer. FOX Racing Shox for further inspection and repair.
This video is a little more to the point. This feature is not available right now. Please try again later.
- Find the best mountain bike forks from Competitive Cyclist available online. Talk to one of our specialists today.
- All Manuals General CTD Remote Installation (2014-2015 models) DOSS Adjustable-Height Seatpost FORK- General Information and Installation Guide SHOCK- Eyelet and Air.
- 36 TALAS AIR SPRING SETTING guidelines: Rider Weight: Air Pressure < 125 lbs. 45 psi: 125 - 135 lbs. 48 psi: 135 - 145 lbs. 50 psi: 145 - 155 lbs. 53 psi.
Check headset adjustment. If loose, adjust according. Check that brake cables or hoses are properly.
Check that the front and rear brakes operate properly. Setting Sag. You can also view a Flash. Setting Sag. To get the best performance from your fork, it is necessary to set and.
Generally, sag should be set to 1. Unscrew the center. TALAS lever (shown below) on top of the. Schrader valve. Hold the TALAS lever steady with one hand while unscrewing. This will facilitate removal of the aircap. TALAS lever from being forced past its stops.
Set the lever in the. Attach a FOX Racing. Shox High Pressure Pump to the Schrader valve. Using the 3. 6. TALAS Air Spring Settings table below, pump your fork to the appropriate. BSPSPopup. On. Mouse. Over) == 'function') BSPSPopup.
On. Mouse. Over(event); " class="BSSCPopup" onclick="BSSCPopup('././using_the_fox_high_pressure_pump. FOX High Pressure Pump. Install a zip tie with.
Carefully sit on the. The fork should compress slightly.
Being careful not to. Measure the distance. This distance is sag. Compare your sag measurement. Sag Setup table below. If your sag is lower than on the table, screw on the pump fitting. Measure sag again and repeat adjustment.
If your sag is higher than on the table, screw on the pump fitting. Measure sag again and repeat adjustment if necessary. Screw the blue aircap. TALAS. AIR SPRING SETTING guidelines.
Rider Weight. Air Pressure< 1. Travel. XC/Race FIRMFreeride PLUSH1. Sag and spring rate.
TALAS is adjusted to. Symptom. Remedy. Too much sag(+) air pressure in 5psi increments. Too little sag(- ) air pressure in 5psi increments. Excessive bottoming(+) air pressure in 5psi increments. Harsh ride; full travel not utilized(- ) air pressure in 5psi increments. Adjusting Rebound.
The rebound knob (shown below) is located on the top of the right fork. Rebound controls the speed at which. Turning the knob clockwise. As a starting point, turn the rebound adjuster knob all the way clockwise. Knob Setting (clicks out from full in)Setting Description.
Tuning Tips. Setup Tips. Slow Rebound. Too slow and your fork will pack down and ride harsh. If you increase your spring rate or air pressure, you will need to slow. Factory setting)Average Rebound. Fast Rebound. Too fast and you will experience poor traction and wheel hop.
If you decrease your spring rate or air pressure, you will need to speed. Adjusting High- Speed Compression. RC2 only)High- speed compression damping. This adjuster rotates to stops at each end. It is preset from the factory at 1 click. The knob is protected.
Never ride your FOX 3. Knob Setting (clicks IN from full OUT)Setting Description. Tuning Tips. 1Slow Compression.
Maximum wheel traction and bump compliance. If setting is too soft. G- outs. 1(Factory setting)Average Compression. Firm Compression.
Reduces bottom- out and provides maximum bump absorption. If setting. is too firm, you may experience a harsh ride with bad traction and use. Boost" Feature of the High- Speed Compression Adjuster (RC2.
The high- speed compression adjuster is equipped with a maximum “Boost”. This setting offers increased bump force resistance well beyond.
To enable the “Boost” feature, turn the high- speed compression knob to. You can use a 3mm hex key to assist in turning the knob to the full in. Boost feature. Adjusting Low- Speed Compression. RC2 only)Low- speed compression damping controls the influence of the rider’s.
This adjuster rotates to. It is preset from the. The. knob is protected by the black protective cap. Never ride your FOX 3. Knob Setting (clicks IN from full OUT)Setting Description.
Tuning Tips. 1Slow Compression. Maximum wheel traction and bump compliance. Too soft and you maybe have. Factory setting)Average Compression. Firm Compression. Resists brake dive and keeps the fork up in the travel. Too firm and. you may have poor traction in loose conditions.
Hydraulic Bottom- Out System. The 3. 6 VAN is equipped with a patent- pending Internally Adjustable Hydraulic. Bottom- Out Control System. This feature can be adjusted inside the cartridge. FOX Racing Shox or an Authorized.
Service Center. It comes preset from the factory at the FIRM setting. Changing Travel. 36 TALAS forks feature three externally adjustable travel.
TALAS lever (shown below) on top of the left. Travel options and direction settings are printed directly on. When changing travel, the TALAS II system automatically. There is no need to re- adjust the air pressure in. TALAS air chamber after changing travel. For safety reasons, it is recommended that travel adjustment. If necessary, travel can be adjusted on- the- fly.
Decreasing Travel. From the 1. 60 or 1. Travel will be decreased in 3. Do not. force the lever past the 1.
Increasing Travel. From the 1. 00 or 1. Travel will be increased in 3. Do not. force the lever past the 1.